SUCCESS!!
Finally I got the voice commands working! SO here's a summary of my case:
At first, the car came with 1.0 and I was told by Ford to upgrade to 2.3... big mistake. Upgrade went fine, no errors but Voice Control was gone, when pressed the button on the steering wheel, it showed the message "Voice control not ready". Dammit.
Then I came here, did a LOT of reading, researching, learning and asking, and finally came out with this:
1. Installed 2.2, in three steps:
Step 1:
Code:
; Gen 3 - Assembly Update - NonNav/NEU - 17011
[SYNCGen3.0_2.2.17011_PRODUCT]
Item1 = HB5T-14G386-TBB
Open1 = SyncMyRideHB5T-14G386-TBB.tar.gz
Options = AutoInstall
[SYNCGen3.0_ALL]
Item1 = HN1T-14G381-SA
Open1 = SyncMyRideHN1T-14G381-SA.tar.gz
Item2 = GB5T-14G386-AA
Open2 = SyncMyRideGB5T-14G386-AA.tar.gz
Options = AutoInstall,Delay,Include,Transaction
Step 2:
Code:
; Gen 3 - Assembly Update - NonNav/NEU - 17011
[SYNCGen3.0_2.2.17011_PRODUCT]
Item1 = HB5T-14G386-TBB
Open1 = SyncMyRideHB5T-14G386-TBB.tar.gz
Item2 = GB5T-14G386-SB
Open2 = SyncMyRideGB5T-14G386-SB.tar.gz
Options = AutoInstall
[SYNCGen3.0_ALL]
Item1 = HN1T-14G391-BC
Open1 = SyncMyRideHN1T-14G391-BC.tar.gz
Item2 = GB5T-14G386-AA
Open2 = SyncMyRideGB5T-14G386-AA.tar.gz
Options = AutoInstall,Delay,Include,Transaction
Step 3:
Code:
; SYNC3 2.3.10 NonNav install GN
[SYNCGen3.0_ALL]
Item1 = HN1T-14G423-CA
Open1 = SyncMyRide\HN1T-14G423-CA.tar.gz
Options = AutoInstall,Delay,Include
At this point, I had 2.2 fully functional, including Voice Control (yay!), but I wanted my system fully up-to-date, so I went ahead and installed 2.3, but with a little modification:
Step 1:
Code:
; SYNC3 Consumer Assembly Upgrade - Release 2.3.10 - Only for MY 16 NonNav/NonEU assemblies.
[SYNCGen3.0_2.3.17109_PRODUCT]
Item1 = HB5T-14G386-TBB
Open1 = SyncMyRide\HB5T-14G386-TBB.tar.gz
Item2 = HB5T-14G386-AHH
Open2 = SyncMyRide\HB5T-14G386-AHH.tar.gz
Item3 = GB5T-14G386-SC
Open3 = SyncMyRide\GB5T-14G386-SC.tar.gz
Item4 = JL7T-14G391-BB
Open4 = SyncMyRide\JL7T-14G391-BB.tar.gz
Options = AutoInstall
; 2nd half
[SYNCGen3.0_ALL]
Item1 = HB5T-14G387-AAB
Open1 = SyncMyRide\HB5T-14G387-AAB.tar.gz
Item2 = JL1T-14G381-AJ
Open2 = SyncMyRide\JL1T-14G381-AJ.tar.gz
Item3 = GB5T-14G386-AA
Open3 = SyncMyRide\GB5T-14G386-AA.tar.gz
Options = AutoInstall,Delay,Include,Transaction
Step 2:
Code:
; SYNC3 2.3.10 NonNav install GN
[SYNCGen3.0_ALL]
Item2 = JL7T-14G423-BA
Open2 = SyncMyRide\JL7T-14G423-BA.tar.gz
Options = AutoInstall,Delay,Include
As you cansee, I installed everything except GN on the first step, ang GN by separated on the 2nd step. By doing this, I was trying to avoid the dreaded MEM_ERR03 error, so I wouldn't have to start all over again. In the end, I have now fully functional Sync 3 v2.3, including Voice Control.
On a conclusion note, I would like to think that my error was trying to update from 1.0 to 2.3 in one step. I had to go from 1.0 go 2.2 to 2.3, but since Ford sent me the 2.3 zip file, I thougt it was safe to do as the manufacturer says... well, wasn't on this case.
HUGE thanks to
Acool, from
www.f150forum.com, this guy helped me a lot, couldn't have done it without his guidance.
DISCLAIMER: This process worked for me, and may not necessarily work for everyone, so try at your own risk!
Here's proof!
https://www.youtube.com/watch?v=M5gQJoxhtwQ
Thanks!!