Latest Activity
-
Hub size is different also. You'd need a centering ring IIRC. -
M-Sport fan replied to the thread OEM-Ish Equipment... What are my options?.If they used higher rate linear springs which could allow for even close to factory ride height on the adjustable collars, it would also... -
Finally pulled the trigger on a set of B14s since they were <$1000 shipped on clearance. Anything I should do while I'm in there? Front...
-
Just a plug for off the shelf DIY spring setup that think turned out really well. Spring rates near the Swifts and stock ride height...
-
I did a half a$$ Si-R conversion that they sold in Japan and EU, mainly a B16 swap and a badge lol.
-
M-Sport fan replied to the thread (Possibly) Blew a head gasket looking for suggestions.Does anyone offer billet impeller/shaft snails for our application, regardless of $$$$$?
-
M-Sport fan liked arlisscm's post in the thread (Possibly) Blew a head gasket looking for suggestions.Continued...
-
M-Sport fan liked arlisscm's post in the thread (Possibly) Blew a head gasket looking for suggestions.Photo dump inbound. (Attachments for mass upload)
-
M-Sport fan liked arlisscm's post in the thread (Possibly) Blew a head gasket looking for suggestions.Other than oil in the exhaust (which will eventually burn off) it doesn't appear to of hurt anything else aside from itself and the...
-
M-Sport fan liked daloonie's post in the thread (Possibly) Blew a head gasket looking for suggestions.Oooh a new contender to the Beyblade X World Championship 2026? I feel with you, so much work only for another part to fail. Hurts...
-
New to me shift knob I picked up from @Feisty Fiesta. My old one had a big ugly worn spot on the pleather. Also chasing EVAP codes... -
XanRules replied to the thread OEM-Ish Equipment... What are my options?.Finally pulled the trigger on a set of B14s since they were <$1000 shipped on clearance. Anything I should do while I'm in there? Front... -
XanRules replied to the thread Amp Wiring - Do I Have This Right?.Perfect, "any keyed 12v" is good enough. Thank you! Great, that's what I thought it meant too but I wanted to make sure. Thanks dudes...
-
I think it was black but not positive 🤷🏼♂️ I used a multimeter and cycled the ignition to verify it's only active with key on, I can...
-
For ground it says this: I interpret this to mean that the amp should be grounded to the chassis nearby with a short wire. It is not...
-
Mmadhatter replied to the thread ISO Kosei K1.Hub size is different also. You'd need a centering ring IIRC.
-
-
arlisscm replied to the thread (Possibly) Blew a head gasket looking for suggestions.Photo dump inbound. (Attachments for mass upload)
-
-
SSteveS replied to the thread Amp Wiring - Do I Have This Right?.For ground it says this: I interpret this to mean that the amp should be grounded to the chassis nearby with a short wire. It is not...
-
XanRules replied to the thread Amp Wiring - Do I Have This Right?.Sorry, I might not be explaining this correctly. There’s a 14g wire hard-wired into the amp’s wiring harness for power, and it’s like a...
-
New here but loving my fiesta so far. So much so I sprung for a set of set of 215/45r16 660+'s on 16x8's to replace the snow tires and... -
New tires are on, RE71RS 205/50r15. They are downsized from the RT660s I ran last time which were 225/45r15. They should be able to hold...
-
Scored brand new rain guards from another member, more excited about these than I should be.
-
Fusion Works replied to the thread ISO Kosei K1.You could machine the wheel for lug nut inserts and just offset the insert 4mm when you bore the hole to fit.
-
There were no R versions of anything until the NSX in 1992. Before that the R was used to designate motocross models. And there was...
