Boomba Racing Fiesta ST BOV adapter

[Boomba Racing]

Taco Tuesday bump!

 

[mcummings182]

Stupid question - what if you have an intake and install the BOV? Does it just add extra noise?

 

[Butterybunz]

Yes, this BPV spacer is much louder than the sound you hear through an aftermarket intake.

 

[Boomba Racing]

Stupid question - what if you have an intake and install the BOV? Does it just add extra noise?

You would have both noises if you had both pieces, yes.

 

[TheJesterRace27]

Do you have any sound clips of the new adjustable BOV adapter?

 

[Boomba Racing]

Do you have any sound clips of the new adjustable BOV adapter?

I'd have to check with our graphics guy and see.

 

[Boomba Racing]

Plenty in stock.

 

[Boomba Racing]

All colors back in stock and ready to ship!

 

[Triflux]

I'm intrested! Are you ship world wide?

 

[Boomba Racing]

I'm intrested! Are you ship world wide?

Yes we do ship all over the world but if your car is a non-US spec vehicle you will need the following piece: http://www.boombaracing.com/1-5-1-6-ecoboost-engine-50-50-blow-off-valve-adapter-bov/

 

[Triflux]

Yes we do ship all over the world but if your car is a non-US spec vehicle you will need the following piece: http://www.boombaracing.com/1-5-1-6-ecoboost-engine-50-50-blow-off-valve-adapter-bov/

Oh thank you very much!
The install is the same of the US version BOV adapter?

 

[Boomba Racing]

Oh thank you very much!
The install is the same of the US version BOV adapter?

Yes installation will be the same regardless of where you are!

 

[Bushhy]

Got my adapter in, and was so excited to install it. Put the passenger side front on jack stand, and took the wheel off. Maybe im crazy, but I cannot see how you all do it. I cannot reach in there. I have a ball headed allen socket, and plenty of extensions, and I can get into two of the holes, but not the top?

Gave up as I didnt want to get too far in and get stuck. Any advice?

 

[ranger024x4]

Got my adapter in, and was so excited to install it. Put the passenger side front on jack stand, and took the wheel off. Maybe im crazy, but I cannot see how you all do it. I cannot reach in there. I have a ball headed allen socket, and plenty of extensions, and I can get into two of the holes, but not the top?

Gave up as I didnt want to get too far in and get stuck. Any advice?

I had no issues with this method, but ended up not using any extensions for that top bolt. I just did it 'blind'.

CJ pony parts video shows him removing the hot side intercooler pipe directly off the turbo and doing it completely under the car.

 

[ranger024x4]

double post

 

[Boomba Racing]

Have you seen our installation video?

[video=youtube;InwriOx46aI]https://www.youtube.com/watch?v=InwriOx46aI[/video]

 

[Bushhy]

Have you seen our installation video?

[video=youtube;InwriOx46aI]https://www.youtube.com/watch?v=InwriOx46aI[/video]

I have. I will be checking again next week. Didn’t have a whole lot of time to mess with it. I just need to get a lift haha

 

[Boomba Racing]

All colors in stock!

 

[ROCKYFiestta]

MINE JUST ARRIVED TODAY IT WOULD HAVE BEEN FASTER IF I DIDNT MOVE FROM ADDISON (AKA TOWN NEXT DOOR)

I Will post on here how i fare since, i like some, am also cursed with the sausage fingers that cant fit anywhere. got the red one looks great and solid quality

 

[ROCKYFiestta]

started at 1120 am mt finished driving home by 1220 (ie funtestdrive)

i followed the video but i ended up doing it this way since i i dont have a lift

i jacked up tire passenger side front and removed the tire . i found it easier to work by sitting in my ice fishing chair directly facing the brake rotor and i did the removal from this angle not from underdeath. i had to much difficulty from underdeath not enough room if you have big arms and hands.

also the tools i used was the smallest ratchet with long extension like 9" a wobble joint at the end of that extension and then i used the allen head bit that is partsocket/allenhead in one piece (found it at lowes around the allen wrenches and sockets). with the wratchet and wobble and extension with the bit definitely made it a breeze
you can clearly see the 2 bolts and just basically triangulate where the 3rd one will be i just searched blindly with my fat fingers and found it put the bit in in gave it some slight twists and eventually i ratcheted it off. cleaned attached the piece as shown in the video i also made note to face it the same way i took it out.