Black 2016 FiST

Member ID
#12844
Messages
16
Likes
19
#1
Picked up a Black 2016 Fiesta ST with 10k miles from a local dealer in Leesburg, VA. I have been around the Ecoboost community for a long time with a 2010 SHO (gone) and a 2016 SHO (still have) that is heavily modded with a hair under 500awhp last dyno run...

I suspect this FiST has been tuned and/or had stuff done but then swapped back to stock. Found a spanner wrench in the glove box, a failed emission test due to the ECU not in readiness state, and the cat looks practically new...

Excited to check out the forum and see what everyone is doing for aftermarket stuff!





Sent from my iPhone using Tapatalk
 


wetwea33

Active member
Member ID
#8616
Messages
634
Likes
494
#2
Picked up a Black 2016 Fiesta ST with 10k miles from a local dealer in Leesburg, VA. I have been around the Ecoboost community for a long time with a 2010 SHO (gone) and a 2016 SHO (still have) that is heavily modded with a hair under 500awhp last dyno run...

I suspect this FiST has been tuned and/or had stuff done but then swapped back to stock. Found a spanner wrench in the glove box, a failed emission test due to the ECU not in readiness state, and the cat looks practically new...

Excited to check out the forum and see what everyone is doing for aftermarket stuff!





Sent from my iPhone using Tapatalk
Looks like you have 1552 cup spoilers too

Sent from my SM-G975U using Tapatalk
 


OP
stealbluesho
Member ID
#12844
Messages
16
Likes
19
Thread Starter #3
Looks like you have 1552 cup spoilers too

Sent from my SM-G975U using Tapatalk
Yes, however, the paint and fit is slightly off. Really curious the history on this car.




Sent from my iPhone using Tapatalk
 


OP
stealbluesho
Member ID
#12844
Messages
16
Likes
19
Thread Starter #6
Thank you! Anyone use SCT on these? If so, anyone have a base config file with the PIDs that are usually monitored? TIA!!


Sent from my iPhone using Tapatalk
 


OP
stealbluesho
Member ID
#12844
Messages
16
Likes
19
Thread Starter #7
Thank you! Anyone use SCT on these? If so, anyone have a base config file with the PIDs that are usually monitored? TIA!!


Sent from my iPhone using Tapatalk
Quoting myself... a quick googling answers that question...

My extra SCTx4 will not be that useful..


Sent from my iPhone using Tapatalk
 


OP
stealbluesho
Member ID
#12844
Messages
16
Likes
19
Thread Starter #10


Found this guy too (I asked about it on another thread) but quickly found it to be a Woosh RMM with their race bushing...

The NVH all makes sense.. I though it just needed some plugs, tires checked, and TLC...

Anything else I should look for? Intake, exhaust, and Intercooler look stock...


Sent from my iPhone using Tapatalk
 


Dpro

6000 Post Club
Member ID
#7958
Messages
6,363
Likes
5,994
#11


Found this guy too (I asked about it on another thread) but quickly found it to be a Woosh RMM with their race bushing...

The NVH all makes sense.. I though it just needed some plugs, tires checked, and TLC...

Anything else I should look for? Intake, exhaust, and Intercooler look stock...


Sent from my iPhone using Tapatalk
thats not a Whoosh RMM thats a AWR and its running a 95 durometer bushing on the large side. Which is why your getting NVH.
 


OP
stealbluesho
Member ID
#12844
Messages
16
Likes
19
Thread Starter #12
thats not a Whoosh RMM thats a AWR and its running a 95 durometer bushing on the large side. Which is why your getting NVH.
My bad, looks like woosh is just a reseller. But you are 100% correct.


Sent from my iPhone using Tapatalk
 


Ford Community Posts



Top