P0012, P0014, and P0330 after engine and turbo overhaul

[Rocketst]

Check your phasers. Mine loosened up when I was working on my car. Not sure what caused it but what you’re describing is what happened to me.

It's a new crate from mountune. It's got 10 miles on it

Sent from my moto z4 using Tapatalk

 

[Rocketst]

So the plot thickens now getting low fuel pressure and cylinder 3 misfire. There any Ford master techs on these forums?

Sent from my moto z4 using Tapatalk

 

[Rocketst]

So I went through everything, all hoses, vacuum lines, and wires. The only thing it could possibly be is 1 one of the solenoids or 2 my cams are actually off. So with piper cams... I'm pretty sure you can set them to advance and retard based on your needs. Will this impact the particular tune I need? I am going to swap out the solenoids with known goods today. If that doesn't work I'm gonna have to break the engine back down and check the cam sprockets.

Sent from my moto z4 using Tapatalk

 

[TyphoonFiST]

Was this Engine Timed before install by mountune ?

 

[Rocketst]

Yes. Also I think I fucked up... I think I forgot the cam bucket...

Sent from my moto z4 using Tapatalk

 

[TyphoonFiST]

Did you find it laying around?

 

[Rocketst]

Well I know I didn't install one but I thought mountune did. But remembering that it sits right underneath the hpfp I know I didn't check if it had one in there...

Sent from my moto z4 using Tapatalk

 

[TyphoonFiST]

I hope they would considering its a long block

 

[TyphoonFiST]

I think they should have any Dynamometer for the Engines and run them to break them in before they send them for that price!

 

[Rocketst]

I agree but honestly I knew what I was getting myself into when I got literally the first one...

Sent from my moto z4 using Tapatalk

 

[Rocketst]

Well that's definitely not right....

Sent from my moto z4 using Tapatalk

 

[JDG]

Well that's definitely not right....

Sent from my moto z4 using Tapatalk

Uh Oh! Well at least you found your problem... I recommend you spin the crank by hand and check the wear on the cam lobe...

 

[Rocketst]

So that fixed my fuel issue. Also installed the new solenoids but nothing really changed there... Starting to look more and more like the timing is actually fucked up..

Sent from my moto z4 using Tapatalk

 

[TyphoonFiST]

Mountune should've sent a doesn't come with Parts list....maybe they can learn from this. Have you contacted them?

Sent from my SM-N950U1 using Tapatalk

 

[Rocketst]

Mountune should've sent a doesn't come with Parts list....maybe they can learn from this. Have you contacted them?

Sent from my SM-N950U1 using Tapatalk

Yeah I did this afternoon. They are gonna help me figure it out. The techs are talking with the engine builders to try to figure out what happened.

Sent from my moto z4 using Tapatalk

 

[TyphoonFiST]

Yes....that is good to hear! I am Happy for you buddy....some actual good info from the source help instead of hearsay.

Sent from my SM-N950U1 using Tapatalk

 

[Rocketst]

I just don't understand how you f up the timing. Like it's basic engine building 101

Sent from my moto z4 using Tapatalk

 

[Ford ST]

Well damn. I was really hoping the solenoids were bad.
I just don't understand I guess because you had those codes on the last engine.

Sent from my LG-LS997 using Tapatalk

 

[D1JL]

I have heard that this engine was not that easy to get the timing correct.
When the cams were changed on my '11 SES, we also had trouble.
This is why I suggested to check the timing belt first.

 

[Rocketst]

I have heard that this engine was not that easy to get the timing correct.
When the cams were changed on my '11 SES, we also had trouble.
This is why I suggested to check the timing belt first.

I get you man but I don't have the tools necessary to roll the cams. Also I'd be taking on a lot of risk. Mountune works the entire motor other than the valve cover and the wiring and stuff... Everything except for the cams are working appropriately now so basically if it screws up it's on them. Of course I want it to work, I don't wanna mess it up. But at the same time I'd rather them give me step by step instructions and possibly get Ford involved. Right now they need me to switch to stage 0 and take a log.

Sent from my moto z4 using Tapatalk